Dan Maresca on DVR Forgets DDNS setup info
Hello, If the CMOS battery was dead it would not be saving date and time either. When it does not work typically it is from the firewall/router blocking the request or the dvr needs to be updated....
View Articlegramps on DVR Forgets DDNS setup info
Thanks, yes the date stays current. It is not so much that it does not work or is blocked by anything. When it quits we go into config DDNS, select DYNDNS from the dropdown and everything is blank....
View ArticleDan Maresca on DVR Forgets DDNS setup info
When you pick the dyn option there should also be a check box off to the side that has to be checked as well. Once everything is entered then you click save at the bottom. If you miss the box it would...
View ArticleTed on DVR Forgets DDNS setup info
Gramps - I think I know what you are seeing. When you open the DDNS page it defaults to Quickddns. (and shows it is not set up) Then if you click the drop down and choose Dyndns - it should show all...
View Articlegramps on DVR Forgets DDNS setup info
No when I select DYNDNS from the dropdown, none of my info is in there. I enter it and it works for a while. I am sure I am hitting save as it would not work if I did not hit save correct? Though I...
View Articleatlambros on Please help me connect to my DVR
Hey guys, I'm having trouble connecting to my DVR. I'm using the general config tool and it is locating my DVR but when I click login this message keeps popping up. "Note: Current device IP and PC IP...
View ArticleHeath Phillips on Please help me connect to my DVR
Are you positive that your PC and computer are assigned IP address to the same network range? Just because the DVR and PC are plugged into same router does not mean they are configured to the same...
View ArticleDan Maresca on Please help me connect to my DVR
Helo, That means your dvr is not in the same ip range as the network you have it connected to. You have to change it to match. Before you do you have to find out what you have.
View Articleatlambros on Please help me connect to my DVR
How do I see what range I need to be in? I'm sorry, I'm not very good with networking.
View ArticleHeath Phillips on Please help me connect to my DVR
Open command prompt on your PC, windows key & "R" at the same time. A run box will poop up, type CMD and kit enter. Once in command prompt, type ipconfig and hit enter, that will tell you the IP...
View ArticleTed on Please help me connect to my DVR
Looks like Heath beat me to it - but here you go anyway = On your PC keyboard - find the Windows 'Flying Flag' key between Ctrl and Alt on the lower left - hold that down and press R one time. That...
View ArticleClik here to view.
atlambros on Please help me connect to my DVR
ipconfig is showing some big IPv6 address that I have never seen before.
View Articleatlambros on Please help me connect to my DVR
and the IPv4 address is 10.1.XX.X which is also not my static IP.
View ArticleTed on Please help me connect to my DVR
Ok then - the 10.1.x.x is your LAN address on the PC. You'll need to have the NVR addressed as 10.x.x.x - first three numbers must match, last number must be different. You will use that number to...
View Articleadmin529 on having an issue connecting up #IPPTZ-EL2L12X-Mini-O 12X 2...
I am looking to get the detailed wiring diagram for this unit thank you
View ArticleJose Malave on having an issue connecting up #IPPTZ-EL2L12X-Mini-O 12X 2...
With most of our IPPTZ's you must power it with the supplied 24 VAC Power Supply and connect an ethernet cable to the camera. This will add the camera to the network where your recorder will see its...
View Articleking on IP-HFW4300S and IPC HDB4300C picture problem
Hello, i upgraded my IP-HFW4300S and IPC HDB4300C from 2.420.0008.0 to 2.420.0000.10 because i was having problem with motion detection, but after upgrading both cameras, the picture is very laggy and...
View ArticleDan Maresca on IP-HFW4300S and IPC HDB4300C picture problem
Have you tried defaulting them since you updated them?
View Articleking on IP-HFW4300S and IPC HDB4300C picture problem
yes, i have default them and use a config cleanup tool to clean all the settings. here is the current settings of one of the camera. code-steam Type: regular compression: H-264 Resolution: 1920X1080...
View ArticleDan Maresca on IP-HFW4300S and IPC HDB4300C picture problem
It is the firmware doing that. if the camera has the factory reset option in the web service that is the default I would use. If not try reloading the firmware onto it. if reloading the firmware does...
View Article