Howdy Dan & Jessica, some more info updates for your consideration.
Photo of dvr monitor screen (main>operate>search), channel 17 (ELI-SIP-EMVD-21-4R) recording skips at 3PM-4PM
Photos of dvr monitor screen (main>log), 2016/1/22 at 2PM-3PM
Log #1 - #13 channel 17 recording skips. Log #1 -#30 repeat same message.
Log #31-#41 during my (main> search) session to review recordings.
Photos of dvr monitor screen (main>log), 2016/1/22 at 3PM-4:30PM
Log #1-#10 is during scheduled automatic reboot. #11-#13 show channel 17 beginning is record skips again.
Log #14-#26 channel 17 recording skipping again, dvr not being accessed by anyone.
Dan:
So though the “Event” doesn’t say error, I think this is what you are asking for Dan when you asked “Also please recheck logs on dvr for any error codes”.
As today we are having s high wind warning event going on today and thru the night, I am not comfortable making any settings work or taking the camera off line due to chance of power going down in the middle of session. Will try to follow Dan’s instructions tomorrow to “delete the camera off dvr? Re-verify the camera is holding the settings then re- add it to remote device”.
I will take photos after I do that to show what I get on the
I will then take photos of the Web Stream Configuration for Stream and one of the DVR Encode menu to show the settings listed in them.
I have made no camera setting changes since I set the camera to FPS to 15, change to VBR Bit Rate 1500 as per your instruction’s Dan, using the WEB service on 2016/1/25.
FYI, note that since those setting were made, so far no skips in the recording.
I need to know what I have lost in performance capability for the camera by downgrading the
VBR Bit Rate down to 1500? That is what is the loss to the cameras optimal functioning?
And I would prefer the 30 fps the camera and dvr are supposed to achieve, as that makes for a smoother viewing picture, and no missed details when reviewing the recordings. The Hybrid Federal Model: HYBDVR-Feo16480 should be able to handle that considering I am only running 7 of a possible 16 analog, and 2 of a possible 16 IP cameras shouldn’t it?
Jessica:
I am thinking that right now with the dvr already recording straight through using the lower fps and VBR rate settings, power must not be the problem?
Or should I be setting it back to the default settings it had prior to setting in Dan’s settings, and then follow your instructions you sent?
I am a bit confused to what path to take here?
I would like to have the camera going at the 30fps and 2048 bit rate, would be higher grade system wouldn’t it?
My other IP camera (IPPTZ-EL2L12X) PTZ camera is running fine with the 30.fps a 2048 bit rate, no problems.
Dan & Jessica:
FYI, I noted today, looking at the DVR’s (main>camera>encode) settings for camera 17, it DID show the change in the Bit Rate Type from its old CBR to the VBR, AND the Bit Rate from 2048 to the new 1500. BUT the Frame Rate (FPS) still list 1 and not the 15 that was set? Also when I clicked the dropdown options in the Frame Rate (FPS) field, it still only gives a choice of 1 to 12?
I did not make any changes in this menu, just looked to see what it now listed after Dan’s changes I made the other day. Wondering why some changes are carried into this menu and others are not?
Photo DVR (main>system>camera>encode) after entering Dan's settings into the Web log in to camera menu the other day. Note some changes but not all to what had been there, see photo [5] in post 1 at top of this topic for what was there prior to the Dan changes.
